Quantcast

Maximum PC

It is currently Tue Nov 25, 2014 5:59 pm

All times are UTC - 8 hours




Post new topic Reply to topic  [ 15 posts ] 
Author Message
 Post subject: Military PC Build for Raptr.com - Final Pics
PostPosted: Fri Nov 18, 2011 1:51 pm 
Little Foot
Little Foot

Joined: Thu Jun 29, 2006 1:21 pm
Posts: 178
Location: Northern Cal
Hey everyone,

This case mod is being built for Raptr.com, for their Battlefield 3/Call of Duty Modern Warfare 3 Showdown. Members vote on which game they think is better, then I will base the theme of this case on which game gets the most votes. :)

Here are some early conceptual designs I made up, using various cases:
Image

Around the same time I was building the Level 10GT case mod, and Raptr requested I incorporate some of the features used in that mod into this one. So the minigun was integrated into the design.
Image

Then Cooler Master came through and provided their new Trooper case, which lent itself well to the theme. So new concepts were drawn up:
Image

Fortunately, since both games are military styled, I don't have to wait for the outcome to get started. First, I'd like to thank the following sponsors for this project, especially Raptr for giving me this opportunity! :D
Image

Image

Image

Image

Image

Here are a couple shots of the Trooper case:
Image
Image
Image
Image

And now we get to the goodies, courtesy Origin PC:
Image

And finally disassembly of the Trooper case:
Image

Now to start some actual work!


Last edited by Boddaker on Sat Jan 28, 2012 11:15 pm, edited 5 times in total.

Top
  Profile  
 
 Post subject: Re: Military PC Build for Raptr.com
PostPosted: Fri Nov 18, 2011 1:55 pm 
Little Foot
Little Foot

Joined: Thu Jun 29, 2006 1:21 pm
Posts: 178
Location: Northern Cal
First item up for build is the minigun. I'll be doing pretty much the same thing as I did in my Level 10GT mod, but this one will be slightly smaller. So I got some 3/4" acrylic tube, and cut some circles.
Image

Using my miter saw, I cut the tubes down to 1' lengths.
Image

Scuffed all parts.
Image

Starting assembly, fitting the tubes in the holes.
Image

All rings spaced appropriately.
Image

And a shot of the minigun in the case for placement.
Image

I'm thinking it will have to be lowered to accommodate the placement of the optical drive and Lamptron fan controller in the upper bays. The Trooper case features removable drive cages, so there will be plenty of room to work with. :)


Top
  Profile  
 
 Post subject: Re: Military PC Build for Raptr.com
PostPosted: Sat Nov 19, 2011 8:50 pm 
Little Foot
Little Foot

Joined: Thu Jun 29, 2006 1:21 pm
Posts: 178
Location: Northern Cal
Quick update!

Working on the front bezel, making room for a 200mm fan. First thing I had to do was get some components in there and figure out where the minigun will be. This position looked too low, so I removed the lower bay cover and raised the minigun back up a bit.
Image

Once that was finally established, I could mount the rollers.
Image

Then it was time to hack off the lower half.
Image

Then I cut some flat bar and bent them around the minigun and fan to kind of group them together.
Image

Here's the new frame, pop riveted together.
Image

My idea is to add some mesh to fill in the areas around both the minigun and fan. But that will have to wait til next time.


Top
  Profile  
 
 Post subject: Re: Military PC Build for Raptr.com
PostPosted: Fri Dec 16, 2011 12:04 am 
Little Foot
Little Foot

Joined: Thu Jun 29, 2006 1:21 pm
Posts: 178
Location: Northern Cal
Ok, finally an update on this! :D

Continuing on with the front bezel, I cut some mesh to fit inside my aluminum frame.
Image

I cut it wider than the frame...
Image

...then bent the excess down so it would fit.
Image

Quick test fit on the case with gun. Got to fill the upper corners with something.
Image

So I cut some pieces from scrap black acrylic.
Image

Sanded them down and smoothed them out.
Image

A nice fit.
Image

Next up was to cut the hole for the 200mm fan into the mesh.
Image

I liked the Sniper style fan grill from MNPCTech, so I had Bill make me up one to fit the 200mm fan. :)
Image

Assembled the whole front bezel to see how it looks...
Image

And with some power to the fan... Sweet!
Image

I should have another update for you this weekend. 'til then!


Top
  Profile  
 
 Post subject: Re: Military PC Build for Raptr.com
PostPosted: Fri Dec 16, 2011 9:35 pm 
Team Member Top 50
Team Member Top 50
User avatar

Joined: Wed Sep 09, 2009 4:08 pm
Posts: 1514
Location: Alberta, Canada
Looks pretty cool so far! 8)


Top
  Profile  
 
 Post subject: Re: Military PC Build for Raptr.com
PostPosted: Sun Dec 18, 2011 1:43 pm 
Little Foot
Little Foot

Joined: Thu Jun 29, 2006 1:21 pm
Posts: 178
Location: Northern Cal
magnumsrule wrote:
Looks pretty cool so far! 8)


Thanks magnumsrule!

Another feature borrowed from the Level 10GT COD mod that Raptr wanted in this case was the first aid kit with integrated beverage cooler. First thing I had to do was figure out how to incorporate it into the Trooper case. I ended up going with a smaller kit and placing it towards the front on the left side panel.

Here is the smaller sized first aid box. The handle and latches will be removed.
Image

After removing the mesh portions of the side panel, I added a window and beefed up the edge where the door's hinge will go.
Image

Then I added a piano hinge using pop rivets.
Image

The door is secured to the hinge via flathead screws and nuts.
Image

Testing the door on the case. Closed...
Image

Open. It's a smaller compartment than the other one, but it still can hold a can and maybe some band-aids or something. :)
Image

Now for the internal part of the first aid kit. I grabbed another beverage cooler from Xoxide.
Image

Removed the TEC and wiring from the casing.
Image

Made a hole in the bottom of the box and fit it over the TEC plate.
Image

The box will take the place of the Trooper's removable drive cages. And there's still room on the other side for some drives, just gotta make a new mounting system.

The first aid kit door will be painted black to match the case, after masking off a cross symbol. The inside will remain white.


Top
  Profile  
 
 Post subject: Re: Military PC Build for Raptr.com - First Aid Kit
PostPosted: Tue Dec 20, 2011 5:58 pm 
Million Club - 10 Plus
Million Club - 10 Plus
User avatar

Joined: Wed Apr 15, 2009 8:04 am
Posts: 1307
Location: Lost in a paper bag again...
WOW!! This is awesome! :mrgreen:


Top
  Profile  
 
 Post subject: Re: Military PC Build for Raptr.com - First Aid Kit
PostPosted: Thu Dec 22, 2011 12:37 am 
Little Foot
Little Foot

Joined: Thu Jun 29, 2006 1:21 pm
Posts: 178
Location: Northern Cal
Thanks Graydiggy!

I'm back with another update! This feature of the build came about after I was well into the project. After staring at the case for what seems like hours (and probably was), I realized I could play off of the Trooper's rugged appearance, and add an exterior roll cage. Exo roll cages are common on 4X4 vehicles set up for rock crawling and extreme 4-wheeling. I've seen some military HMMWV's outfitted with them as well, so I thought it would enhance the overall theme here. Both side panels will have a protective cage, and there will be 3 or 4 "bull bars" going across the front bezel connecting them.

So I got some 1/2" acrylic rod and started cutting and bending. Taking the side panel's characteristics into consideration, I drew up a rough sketch of how I wanted the bars to go. I first started with the outer frame, making a U shape, then added the back piece, and finally the center cross bars.

First thing I did was make a bending jig, so my radii would be the same for each bend. I carved out the edge of a piece of wood so the bar wouldn't flatten out at the bend.
Image

Using the heat gun, I could apply intense heat to a very specific area.
Image

After a few minutes, the result is a perfect 90 degrees. :)
Image

For the ends, I used my Dremel to grind them to mate up with the back 1/2" rod.
Image

Fits nicely!
Image

The back piece needed a raised area in the middle, so some 45 degree bends were made using the same jig, just with a lesser bend.
Image

Here you can see how I'm following the contours of the side panel. Now the center cross bars can be measured, cut and bent.
Image

For the other end of the center cross bars, they need to turn down to meet the front.
Image

Coming together! Just need one more vertical center brace.
Image

All pieces made, glued and sanded.
Image

Next step is to make a bunch of stand-offs to raise the roll cage off the side panel, and provide a means for mounting as well. Til then!


Top
  Profile  
 
 Post subject: Re: Military PC Build for Raptr.com - Exo Roll Cage
PostPosted: Thu Dec 22, 2011 10:14 pm 
Little Foot
Little Foot

Joined: Thu Jun 29, 2006 1:21 pm
Posts: 178
Location: Northern Cal
A couple more pics on the mounting of the roll cage...

Tapping the standoffs...
Image


And mounted on the panel.
Image

This one's pretty much ready for priming/painting. Now I have to do the other side as well as the front bull bars.

Cheers!


Top
  Profile  
 
 Post subject: Re: Military PC Build for Raptr.com - Exo Roll Cage
PostPosted: Mon Jan 02, 2012 12:46 pm 
Little Foot
Little Foot

Joined: Thu Jun 29, 2006 1:21 pm
Posts: 178
Location: Northern Cal
New Year's Update!

I had Steve Nunez do some airbrushing for me on the right side panel. After seeing his phenomenal work on DarthBeavis' cases and BOBDBONE's Wonder Woman case, I didn't have to think twice about who was going to do it. I made up a design combining BF3 wallpapers and raptr's Dino mascot. The client ended up wanting something a bit more subtle than our original concept, so the screaming BF3 logo was taken out, and the soldier was replaced with the Dino.
Image

The detail is spot on with the reference images I sent.
Image

A close up of the jet.
Image


I managed to get more work done over the holidays. I pretty much finished the exo roll cage. Got the other side panel done and ready for paint, as well as the front cross bull bars.

With both side panel cages in place, I could get the cross bars sized to fit and their standoffs made and glued on.
Image

All four made. The one on top is actually the bottom piece, which doesn't require standoffs. It will be secured directly to the front bezel.
Image

After reinforcing the standoffs with a 2-part plastic epoxy, I located the mounting holes, drilled and tapped.
Image

They are secured by standard screws from behind the bezel.
Image

Top three mounted.
Image

The bottom piece is screwed directly into the bottom of the bezel.
Image

If it's not too cold tonight, I'll get some painting done. Then I can move on to the top and front cover plates. :)


Top
  Profile  
 
 Post subject: Re: Military PC Build for Raptr.com - Exo Roll Cage
PostPosted: Mon Jan 16, 2012 10:27 am 
Little Foot
Little Foot

Joined: Thu Jun 29, 2006 1:21 pm
Posts: 178
Location: Northern Cal
Got the final cover plates made for the front and top. We're finally in the home stretch!

After placing the Lamptron fan controller and LG Blu-ray drive in place, I took a bunch of measurements.
Image

Transferred those measurements onto a piece of extra aluminum sheet and proceeded to cut out the holes.
Image

Test fit. Needs a bit of fine tuning, but its pretty much there. Don't worry, the green anodizing won't be around for long.
Image

After a few more test fits and minor adjustments, I filed and sanded the edges smooth. Then shot it with some black paint.
Image

With the front done, I could move to the top switch plate, which would be a bit more time consuming. I made a paper template first,
Image

And marked the alu sheet for cutting.
Image

Got rid of the stock fan controller and buttons.
Image

After drilling the mounting holes around the perimeter, and figuring out where everything was going to go, I started drilling my pilot holes.
Image

Used my trusty step drill bit to drill out the holes for the switches and leds.
Image

Got these military fighter pilot toggle switches from Bill Owen. :)
Image

I opted to get the clear ones so I could paint them.
Image

A quick test fit.
Image

Continuing on with the hole-making. I used my square needle file to get the corners first, then it was easy to do the rest with my flat files.
Image

Looking pretty good. Now I gotta get the IO ports positioned underneath to match. Since the stock IO ports were hard-wired to one single circuit board along with the fan controller, I had to dig into my stash to find another set. I did re-use the USB 3.0 ports in their original locations, and the eSATA is the original port, just relocated to the bottom center.
Image

There! Now that looks cool. Just have to do final touches and paint the cover plate. I'll paint the toggle covers red as well. Bill had anodized red ones, but I didn't like how they looked, so I opted to get the clear ones so I could paint to suit.
Image

Image

Here's a final shot of how the whole front looks. Starting to come together now!
Image

This weekend I'll be finishing up the exterior, and moving on to the wiring and component installation. woot!


Last edited by Boddaker on Sun Jan 22, 2012 8:37 pm, edited 1 time in total.

Top
  Profile  
 
 Post subject: Re: Military PC Build for Raptr.com - Switch Plate
PostPosted: Tue Jan 17, 2012 10:21 am 
Little Foot
Little Foot

Joined: Thu Jun 29, 2006 1:21 pm
Posts: 178
Location: Northern Cal
Small update:

Got the toggle switch covers painted red, and the top switch plate fully mounted on the case.
Image

Now on to the minigun motor installation and wiring! Here's all the parts for making the barrel spin.
Image

Here's a shot of the mount I made for the motor. I ended up going with a different motor with more torque, as the first one was a bit weak.
Image

I originally started with equal sized gears, but the barrels didn't spin quite as fast as I wanted. So I swapped them out, going with a larger one on the motor, and a smaller one on the barrel.
Image

So between the higher torque motor and the gear reduction, I got the barrels to spin a lot faster and more consistent. I'll post up a video soon, once I get everything wired up. :)


Top
  Profile  
 
 Post subject: Re: Military PC Build for Raptr.com - Switch Plate
PostPosted: Wed Jan 25, 2012 5:23 am 
Sharptooth
Sharptooth
User avatar

Joined: Sat Nov 20, 2004 3:42 pm
Posts: 380
Location: Mpls, Mn
Bump for an awesome project! :mrgreen:


Top
  Profile  
 
 Post subject: Re: Military PC Build for Raptr.com - Switch Plate
PostPosted: Sat Jan 28, 2012 11:14 pm 
Little Foot
Little Foot

Joined: Thu Jun 29, 2006 1:21 pm
Posts: 178
Location: Northern Cal
FINAL PICS! :D

Image

Image

Image

Image

Image

Image

Image

Image

Image

Image

Image

Image


Top
  Profile  
 
 Post subject: Re: Military PC Build for Raptr.com - Final Pics
PostPosted: Wed Feb 01, 2012 10:14 am 
Little Foot
Little Foot

Joined: Thu Jun 29, 2006 1:21 pm
Posts: 178
Location: Northern Cal
Featured on Bill Owen's Case Mod Blog today! :D


Top
  Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 15 posts ] 

All times are UTC - 8 hours


Who is online

Users browsing this forum: No registered users and 2 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group

© 2014 Future US, Inc. All rights reserved.